 |
|
|
|
|
| Aines
Manufacturing Corp. Product Catalog |
 |
| Click
on the link below to view the product's picture
and features. |
|
|
|
|
|
| CD-1000
Coil & Drain |
| The
Aines CD-1000 Coil and Drain can help
you with these common telephone problems. |
| Coin
Telephones: |
|
Noisy
on out-going local calls, but
quiet |
| |
on
incoming and long distance calls. |
|
Eratic
and noisy circuits due to 60Hz
|
| |
induced
AC voltage. |
|
| Key
Systems: |
|
Heavy
hum on trunk calls. |
|
Off-premise
intercom that is noisy while
the |
| |
on-premise
station is quiet. |
|
| P.A.B.X.
or P.B.X.'s: |
|
Miss
dial due to more than 10 volts, |
| |
60
Hz AC to GND. |
|
Off-premise
extensions noisy, AC problems. |
|
Noisy
trunks. |
|
| Private
Line Circuits: |
|
Not
working properly due to 60 Hz
AC. |
|
Noise. |
|
|
 |
|
| Central
Offices: |
|
Have
unbalanced connectors (many step by step
offices do, the noise only shows up on |
| |
long
lines subject to power influence). |
|
Link
circuits that have a condenser in the tip
and ring (they should be balanced but often
are |
| |
not,
due to replacing of one capacitor). |
|
Unbalanced
loop extenders. |
|
Noisy
DX signaling trunks, CX signaling trunks,
and simplex signaling trunks when exposed |
| |
to power influence. |
|
| Foreign
Exchange Circuits: |
|
Noisy. |
|
60
Hz AC problems. |
|
| If
you have these problems and your trouble
is not caused by bad cable or other facility
problems, solve your problems with the Aines
CD-1000. Just place the CD-1000 at the noisy
location. It works by re-balancing the line,
yet does not insert more than 1 DB of insertion
loss in your circuit. Makes line noise decrease
by 40 DB in worst cases of induced unbalance. |
|
|
|
| Return
to the top
of the screen. |
|
|
| Model
1 "STOPWATCH"® |
 |
| Tone
out CATV CABLES (coax) with the AINES Model 1
"STOPWATCH"®
|
| using
a conventional toner and probe. |
|
Identify CATV riser cables and in house lateral
feeds. |
|
|
| Return
to the top
of the screen. |
| |
|
|
| AMA8
& AMA6 |
| This
handy tool helps determine whether
the trouble is in the phone or in
the line. The unit contains jacks
at both ends. The forward jack contains
the cord and the "K" Plug
that is inserted into the wall jack
or the equipment being tested. |
 |
| The
rear jack enables the Modular Adapter
to be placed in line for continuous
service while testing line conditions. |
|
| Modular
Adapters are available in a 6 and
8 wire configurations. |
|
| Replacement
Cords: |
|
For
6 wire 10" double ended
K |
| |
Plug
Cords Part No. AMAC6. |
|
For
8 wire 10" double ended
K |
| |
Plug
Cords Part No. AMAC8. |
|
For
Special Order Cords, Part |
| |
No.
AMACS (Specify length and |
| |
wiring
configuration). |
|
|
 |
|
|
|
|
| Return
to the top
of the screen. |
|
|
| Belt
Hook |
|
| This
heavy duty oversize Belt Snap Hook. |
| The
Belt Snap Hook (Model BH-2L) will fit any type
set using similar type belt hook. |
|
|
|
| Return
to the top
of the screen. |
|
|
| CTT-140
140 Generator Cordura
Case |
| This
heavy duty cordura carrying case slips
on to any tool belt and fits our 140A/MC
and 140B/MC Tone Generators. |
|
 |
|
|
| Click
here to return to the top
of the screen. |
|
|
| C240-240
Generator Cordura Case |
| This
heavy duty cordura carrying case slips
on to any tool belt and fits our 240
Tone Test Set. |
|
 |
|
|
| Click
here to return to the top
of the screen. |
|
|
| CSP-101
150 Probe Cordura
Case |
| This
heavy duty cordura carrying case slips
on to any tool belt and fits our 150SP
Stationman Probe. |
|
 |
|
|
| Click
here to return to the top
of the screen. |
|
|
| C250SSP-250SSP
Probe Cordura
Case |
| This
heavy duty cordura carrying case slips
on to any tool belt and fits our 250SSP
Stationman Speaker Probe. |
|
|
|
|
| Click
here to return to the top
of the screen. |
|
|
| CC1
Dual Cordura Carrying Case for Tone Generator
& Probe |
| This
heavy duty cordura carrying case slips
on to any tool belt and fits any of
our Tone Generators and Inductive
Probes. |
|
 |
|
|
| Click
here to return to the top
of the screen. |
|
|
| CC2
Cordura Probe Carrying Case |
| This
heavy duty cordura carrying case slips
on to any tool belt and fits any of
our Inductive Probes. |
|
|
|
|
| Click
here to return to the top
of the screen. |
|
|
| #206
Battery for 150SP Probe |
 |
|
The Eveready 206 (9-volt) battery is used to power
our Model 150SP Stationman Probe (shown). |
|
| Click
here to return to the top
of the screen. |
|
|
| B-413
Vinyl Boots for 6A Clip and 6P Clip |
| These
vinyl rubber boots for the 6A and
6P clips are available in the following
colors, blue, green, yellow, black,
and red. |
|
 |
|
|
| Click
here to return to the top
of the screen. |
|
|
| B-416
Rubber Boots for 6A and 6P Clip |
| These
rubber boots for the 6A and 6P clips
are available in the following colors,
blue, green, yellow, black, and red. |
|
 |
|
|
| Click
here to return to the top
of the screen. |
|
